We've encountered this post relating to How to Install a Bathtub below on the web and decided it made sense to share it with you here.
Setting up a bath tub isn't precisely rocket science, however it does require solid plumbing, woodworking, and occasionally, tiling skills. Replacing an old bath tub with a brand-new one is also a moderately tough task. If the old tub is easily accessible, the project can move easily; if you need to open a wall to eliminate the old bathtub and position the new tub, the job is a lot harder. In either case, the job is within a residence handyman's skills, although you will certainly require a helper to move out the old tub and also set in the new one. See to it you have qualified yourself for the work and are comfortable attempting it. As opposed to working with a professional to take control of a halfway-completed task, it is better to think about using one before you begin. Possibilities are you might require a professional plumber to make tube connections.
This post will certainly aid you install a new tub in your shower room if you have actually currently acquired a new tub as well as don't need to alter the setup of your previous water pipes.
Your tools and material checklist must consist of the following:
Removing Old Touches
If you require to change old faucets with brand-new ones as a part of your installment, after that the first thing you need to do is disconnect the water supply. After doing so, turn on the taps to drain any water remaining in the system. The process of removing the existing taps can be quite problematic due to the restricted access that is often the case.
Use a basin wrench (crowsfoot spanner) or a faucet device to reverse the nut that attaches the supply pipelines to the faucets. Have a fabric prepared for the staying water that will come from the pipes. As soon as the supply pipelines have actually been eliminated, utilize the exact same tool to loosen the nut that holds the taps onto the bath/basin. You will certainly require to stop the solitary taps from transforming throughout this process. When the faucets have actually been removed, the holes in the bath/basin will certainly have to be cleansed of any type of old securing substance.
Prior to carrying on to fit the new taps, contrast the pipeline connections on the old taps to the new faucets. If the old faucets are longer than the new taps, after that a shank adapter is needed for the new faucets to fit.
Fitting New Taps
If the tails of the brand-new taps are plastic, after that you will require a plastic port to prevent damages to the string. One end of the connector fits on the plastic tail of the faucet as well as the other end supplies a connection to the current supply pipelines.
If you need to fit a monobloc, after that you will call for minimizing couplers, which connects the 10mm pipeline of the monobloc to the conventional 15mm supply pipeline.
Next, place the tap in the mounting opening in the bath/basin guaranteeing that the washing machines are in area between the faucet as well as the sink. Safeguard the tap in position with the producer provided backnut. When the tap is safely in position, the supply pipes can be attached to the tails of the taps. The faucets can either be linked by utilizing corrugated copper piping or with normal faucet connectors. The previous type must be connected to the faucet ends initially, tightening up only by hand. The supply pipelines can later be linked to the other end. Tighten both ends with a spanner after both ends have actually been connected.
Installing the Tub
Making use of the two wood boards under its feet, put the tub in the required placement. The wooden boards are practical in evenly spreading out the weight of the bathtub over the area of the boards rather than focusing all the weight onto four tiny points.
The next objective is to ensure that the tub is leveled all round. This can be attained by examining the level and readjusting the feet on the bath tub until the level reviews level.
To install faucets, fit all-time low of the furthest flexible faucet adapter to the appropriate supply pipe by making a compression sign up with; after that do the exact same for the various other faucet.
Switch on the supply of water and also examine all joints and new pipework for leakages and also tighten them if essential. Fill the tub and additionally examine the overflow electrical outlet and the typical outlet for leakages.
Ultimately, deal with the bathroom paneling as described in the manufacturer's instruction manual. Tiling and sealing around the tub must wait until the tub has been utilized at the very least when as this will certainly resolve it right into its last position.
Preparing for the Installation
First of all, the supporting framework provided with the bathroom must be fitted (if called for) according to the producer's guidelines. Next, fit the faucets or mixer to the bath tub. When fitting the faucet block, it is important to ensure that if the tap comes with a plastic washer, it is fitted between the bath and the faucets. On a plastic bathroom, it is likewise practical to fit a supporting plate under the taps unit to stop pressure on the bath tub.
Fit the adaptable faucet adapters to the bottom of the two taps using 2 nuts as well as olives (often supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and then pass the outlet via the hole in the bathroom. Use the nut supplied by the supplier to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the versatile overflow pipe to the overflow electrical outlet. After that, screw the pipe to the overflow face which need to be fitted inside the bathroom. Ensure you make use of all of the provided washing machines.
Connect the catch to the bottom of the waste electrical outlet on the bathtub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the catch to the outlet. Attach all-time low of the overflow tube in a similar manner.The bathroom should currently be ready to be fitted in its last setting.
Tiling Around the Bathtub
In the location where the bathroom satisfies the tile, it is essential to secure the joins with a silicone rubber caulking. This is important as the installation can move enough to fracture a stiff seal, causing the water to penetrate the wall surface between the bathroom as well as the tiling, resulting in difficulties with moisture and feasible leaks to the ceiling listed below.
You can pick from a selection of coloured sealants to assimilate your fixtures and installations. They are sold in tubes and also cartridges, as well as are capable of securing gaps approximately a width of 3mm (1/8 inch). If you have a bigger space to load, you can fill it with spins of soaked newspaper or soft rope. Keep in mind to always fill up the bathtub with water prior to sealing, to enable the movement experienced when the bathtub is in usage. The sealer can split fairly very early if you do not consider this motion before securing.
Alternatively, ceramic coving or quadrant ceramic tiles can be made use of to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and also cut to dimension, are also conveniently available on the marketplace. It is advisable to fit the ceramic tiles making use of water-resistant or water resistant adhesive and also cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I was brought to that article about How to Install a Bathtub Yourself from a friend on another blog. Are you aware of somebody else who is sincerely interested in the topic? Take a moment to promote it. Thank-you for going through it.
Visit Site